Facebook Twitter YouTube YouTube RSS

Tamiya Honda CB750F 1/6 scale

By Mario Covalski  

Sometimes, something particular comes about to those lucky modelers who have been doing scale modeling for many years… to compare between two models built by the same author, but ...20 years back. (My dear friends, believe me, I wish I could be 20 years younger, and not writing this editorial :-).


This is my situation, and I find special interest in analyzing not only the skill but also the techniques (with their improvements) that have been carried out.
I don't remember exactly, but let's say in 1980, when I built a 1/6 Tamiya Honda CB750F; time passed and the model was still there, sleeping in my showcase. Then, in 1998, I decided to build the same kit (yes another one!)…again.

First, I remembered why I had given up painting with spray cans. Nowadays, I use to airbrush my models, this practice lets me to get a finest painting job, allowing those small parts or tiny details can be fairly visible, and what is most important, the entire absence of orange peel.

What did it mean to me building "a good "model, 20 years ago?:
A body that had been painted with a Testor spray can, sanded and polished, after 2 weeks. A chassis that had also been sprayed. Most of the parts that had been provided chromed or plated, remained in that way, and by that time, only a few metal paints (silver, aluminum or metallic grey), were widely available for me. On the other hand, I didn't care as much about either techniques or research, but.....anyway, the hobby was fun and details were in fact, the result of my imagination
The model I constructed in 1998 was airbrushed at high pressure, using my usual painting technique. Several coats of varnish were applied over and over with the paint still fresh. After some years, I could appreciate a deep and smooth brightness.....and above all, in scale, because I used proper paints for modeling.

I gave the same treatment to the chassis, getting a shine black different to the rest (so as to get contrast). The chromed of the engine was removed to be painted in chrome silver mixed with aluminum and after several washes, it actually looked very real.
I used several mixes to get different shades of black, obtaining in this way, the proper contrast. Drybrush was applied in a very subtle way, just for lightning purposes; drybrushing excessively would make that surfaces look like "stone".

If both models were compared, anyone could immediately appreciate that the latest has more realism and "life", and that the whole assembly looks much more fine.

Everything mentioned above, aims at showing how my techniques have changed along 20 years, and not to judge if they're good or not, and perhaps other modelers' experience could be different. What is most important, the progress in the use of the those techniques. Furthermore, both models lack of aftermarket, so it's possible to move forward, getting better models, without thinking about adding detailing parts. Sometimes, it's just a matter of learning new techniques, or improving our own skill.

Nowadays, many people think that improving a model, say to do "something better" means to buy details sets, or special paints, or to search for more and better references.....I, sincerely believe, that there's no great mystique about. First of all, we should have to be enthusiastic, to develop our skill to the utmost, and to discover that, with simple materials, it's possible to build the model we've dreamed of, these could just be the reasons that would let us improve it..........even after 20 years. 

Comment in Facebook



MODELERSITE.COM takes no responsibility and assumes no liability for any content posted by users or any third party and they will be liable for any damages of any kind, including, but not limited to direct, indirect, incidental, punitive, and consequential damages.


Subscribe our Newsletter


LATEST NEWS


Editorials

Editorial

The best of 2018 Over the end of the year, we are offering a preview of the articles we were proud to have during 2018. Enjoy them and happy new year.




Showcases

By Modeler Site

Problems downloading files

By Mario Covalski

Building the RC Leopard 2A4 1/16 scale A couple of years ago, I discover  www.Ludwigs-Hobby-Seite.de, a web site where Christian Ludwig offers his kits mostly made of  plastic, cut with the CNC technology. So, I found a kit to convert a Heng Long 2A6 to the 2A4, that is to say a previous version.

By Mario Covalski

Converting the Trumpeter T-72 MBT to RC 1/16 scale To improve the Heng Long T-90 I read some books and gathered information/photos from the web. This little research made me know more about these compact Russian tanks T-72/T-90, and so it grew my interest in them. So I bought the 1/16 T-72 Trumpeter kit. This kit was designed not only for static but also for RC. The static version has some extra details and modifications, reminds me the, T-34 from WSN, a brand with which Trumpeter sold the T-34 RC. The philosophy of the T-72 is the same, I still believe that the T-34 gearbox with its motors, would fit in the hull. Perfectly.  

By Mario Covalski

Building and improving the Italeri / Protar Alfa Romeo 179 1980 1/12 scale In May 2001 I wrote a brief preview on the Protar's 1/12 Alfa Romeo 179. This wonderful Formula One was one of the few cars in modern F1 history which chassis and engine were the same brand. Is this model really difficult? This is the key question for this model, and the answer is NO. If it were a Tamiya model, that is to say the same matrix but injected with Tamiya plastic and having the quality control of this huge Japanese company, I would say that this is one of the most delicious models I have ever built. Unfortunately, it has some flaws, mainly due to its poor quality than to the work of the Protar craftsmen.

By Mario Covalski

Tamiya Caterhams, a step by step guide for novices 1/12 scale The first Catherham from Tamiya coming to my hands at the end of 1994, was the “Cycle Fender Special” (10202), since the “Super Seven BDR was out of stock, and it was impossible for me to get it from the stores I used to buy kits. From that moment on, my affair with which, I think is the best scale car kit ever produced, began. And here my comment: probably, you have seen better detailed kits, or even superb models limited editions.

By Rick & Jannine Bennett

Learning to paint figures step by step

By Mario Covalski

Building 1/12 F1 resin model kits: A step by step guide for novices This article aims at offering an illustrated guide, with pictures, explaining step by step the tasks that should be done, how to and the reasons, it’s basically a visual guide, based on the construction of two MG models: the 2002 Ferrari and the 2003- GA.

By Jose Antonio Solbes

How to paint with lacquers

By Mario Covalski

Building the IDF M50 radio controled Sherman 1/16 scale Building the M50 in 1/16 scale is a project I have had in mind for many years, and after the M51s (from the article published in May 2012) I felt the need to continue with this one. In this article, I’ll share with the reader my experience in building the M50 RC 1/16 from a Tamiya M4 -105mm with HVSS suspension.

By Mario Covalski

Building the Pocher Lamborghini Huracan, step by step, painting guide and tips. 1/8 scale These are the new times of Pocher, hand in hand with Hornby, the brand that offer models which represent high technology subjects as Lamborghini cars and Ducati motorcycles. Manufactured by Ixo, the Chinese company, they are the fashion of the time, huge 1/8 scale cars with metal body and chassis, already painted (luckily!). They compete with Amalgam and other brands with less expectations but to fit any budget and if you have some experience as model builder, the result will be acceptable and even excellent. The aim of this tutorial is to share the step by step in the Lamborghini Huracán construction, the last Pocher issue explaining the work achieved so that it may be useful for less experienced modelers and collectors.

By Claudio Kalicinski

Scratchbuilding the Nieuport 6H, 1/48 scale I decided to scratchbuild this plane after seeing the scale drawings by Mike Fletcher in his web site: The Nieuport Pages. I sent an E-mail to him and he kindly sent me pictures and larger resolution scale drawings. Once I enlarged the plans to 1/48, I noticed how big the plane was....

By Ricardo Gonzalez

Building and customizing the Tamiya Ducati Panigale S 1/12 scale The Ducatti Panigale is to my liking one of the most spectacular motorcycles of the past decade. Thanks to Tamiya we can have a model of it, both were the reasons why I decided to build it trying to get the most detailed model I could , taking advantage of the fact that as it was a mass production model, it would be possible for me to get a lot of references. Not only I built and superdetailed the model, but also made a slightly and own customized version, a real Panigale, as I would like to have. The aim of this article, is to show with pictures and their comments the work accomplished as a guide and to give ideas of the details that can be added or showing in some cases how to do the different tasks.

By Mario Covalski

Improving the Dragon Kubelwagen 1/6 scale # 75003 Action figure collecting is one of the most popular hobbies in the world. Figures made out of different plastic materials based on TV sci-fi series, sci-fi movies (for instance GI Joe action figures) and facts from real life such as the representation of different war scenarios. Soldier figures are commonly made in 1/6 scale, they’re represented with military uniforms made from genuine fabric and the weapons that real soldiers use to have, vehicles included.

By Gary Wickham

Advanced techniques: Building the P-51D Mustang "Lt Col John Myers" Petie 3rd Dragon 1/32 scale The infamous Dragon P-51D in 1/32. This model was started before Tamiya announced their kit, and I have to admit that during this build I did consider scrapping it more than once. In the end, I am very glad I did not. Despite the challenges and limitations of this kit, I am very happy (and proud) of the end result.

By Mario Covalski

Realistic wire wheels for 1/12 scale motorcycles One of the biggest challenges for a modeler who builds motorcycles in 1/12 scale, is to modify a wire wheel and make it look realistic; specially without having to buy an aftermarket kit. Anyway, there are no kits for this kind of modification (except for one of the Acu-stion for the Tamiya XV1600 kit), so it's not possible to get one. So any modeler attempting to do this task must rely in his/her ability in order, to get a good result.

By Denis R.S.Bomfim

Building rusted cars - VW 1966 - 1/24 scale It all started with a joke, I built a rusted Mustang GT 350 to make a gift to a friend who only builds Mustangs. It was at a modelers meeting when he received a homage and the joke consisted of letting him know the arduous remodeling and restoration work he would have with this rusted Mustang. I took advantage of my work and presented it in a contest that took place in Campinas city. Finally, the model was “best of the show” and they called me mad for giving a winning model. My answer was.... I will have to make another rusted model for me.

By Mario Covalski

Improving the Dragon Schwimmwagen - 1/6 scale #75013 Being a car fan, everything that has wheels attracts my attention, nevertheless, the Kubelwagen’s amphibious sibling, went unnoticed by me for quite a long time. After building the 1/6 Dragon Kubel, I was pretty excited with the Schwimmwagen, and the quality of the kit and improvements Dragon introduced a couple of years after the Kubel release, really surprised me. This article aims at offering my view about this kit construction, adding some improvements I considered necessary so as to make a worthy scale model.