Facebook Twitter YouTube YouTube RSS

Building the Mitsubishi EVO IX Montecarlo 2005 from a Tamiya kit 1/24 scale


By Fabio Bonilla  

To carry out this model, I got the Tamiya Mitusbishi Lancer VII WRC (item 24257) and the 1/24 Lancer WRC 05 transkit from Studio 27....


Read More

Mitsubishi EVO IX English BODY {display:none}

Cars

Building the Mitsubishi EVO IX  Montecarlo 2005 version

1/24 scale

by Fabio Bonilla © 2006 Modeler Site

Legal Notice

No material from Modeler Site any Web site owned, operated, licensed, or controlled by Damian Covalski may be copied, reproduced, republished, uploaded, posted, transmitted, or distributed in any way, except that you may download one copy of the materials on any single computer for your personal, non-commercial home use only, provided you keep intact all copyright and other proprietary notices. Modification of the materials or use of the materials for any other purpose is a violation of Damian Covalski's copyright and other proprietary rights.

Read More here > Legal notice


Within the World Rally Championship, there are several surfaces to test the skill of competitors and testing on asphalt is one of them. For the 2005 season championship, 3 stages were run on this surface: Montecarlo, Germany and Catalonia. Perhaps one of the most important is Montecarlo, because it marks the championship starting and due to the continual changes of surfaces from asphalt to snow and worst of all, ice. For the 2005 season, Mitsubishi Corp. and its well known partner in motor sports, Ralliart, presented their last version of the Mitsubishi Lancer, which unlike its predecessor’s, was easier to be driven including the gear shift to the steering wheel.

 


It had a significant aesthetic change which allowed better performances, since the 2004 version didn’t have much success on that point. For the Montecarlo Rally, Mitsubishi introduced two well known racing drivers from the Peugeot Team, they were Guilles Panizzi and his brother Hervé Panizzi in Nº 10 car, and Harry Rovanpera with Pietilainen in Nº 9. After battling until the end of the test, Mitsubishi could see their dreams came true when going up the podium with the 3rd position meaning a great beginning for a season full of emotions and difficulties.


The project

To carry out this model, I got the Tamiya Mitusbishi Lancer VII WRC (item 24257) and the 1/24 Lancer WRC 05 transkit from Studio 27.

 

Then, I searched all the information I could about this car, data coming from Rally World Championship Videos, Internet, and Rally Xpress-Extra magazine issue 04/30, pages 10-28


Pros:

The donor kit is pretty good

A good quality transkit and good PEs

Clear instructions

The transkit is an excellent alternative to have a good replica of this Evo ‘05

 

Cons:

The price of the transkit is nearly the same of a complete resin model

It’s essential to have information to assemble the model, since the instruction sheet shows us the colors to use for the basic parts such as the suspensions, brake discs, interior, controls and accessories.

 


The conversion

I started the conversion by modifying the anti-roll bar, since the one provided with the Tamiya kit is just for the 2001, 2002 and 2003 season. The anti-roll bar has 3 support points, each one parallel to each other. The first pair of points are the bars which support the instrument panel and leans on the chassis base, the second pair are the ones behind the driver and co-driver’s seat and the third and last pair are those leaning on the rear fender.


This note is offered in PDF format to be read or printed using Acrobat reader, contact our webmaster > Here

Includes more than 44 pics, here we show only the text pages.

 

Esta Nota es ofrecida en formato PDF, el cual puede ser leído o impreso usando el Acrobat reader, contacte a nuestro webmaster > Aquí

Incluye más de 44 imágenes, aquí solo mostramos las paginas de texto.

 

   

Big size photos are only available in our PDF format.


Support us ordering our notes in PDF > Here


Comment in Facebook



MODELERSITE.COM takes no responsibility and assumes no liability for any content posted by users or any third party and they will be liable for any damages of any kind, including, but not limited to direct, indirect, incidental, punitive, and consequential damages.


Subscribe our Newsletter


LATEST NEWS


Editorials

Editorial

The best of 2018 Over the end of the year, we are offering a preview of the articles we were proud to have during 2018. Enjoy them and happy new year.




Showcases

By Modeler Site

Problems downloading files

By Mario Covalski

Building the RC Leopard 2A4 1/16 scale A couple of years ago, I discover  www.Ludwigs-Hobby-Seite.de, a web site where Christian Ludwig offers his kits mostly made of  plastic, cut with the CNC technology. So, I found a kit to convert a Heng Long 2A6 to the 2A4, that is to say a previous version.

By Mario Covalski

Converting the Trumpeter T-72 MBT to RC 1/16 scale To improve the Heng Long T-90 I read some books and gathered information/photos from the web. This little research made me know more about these compact Russian tanks T-72/T-90, and so I grew my interest in them. So I bought the 1/16 T-72 Trumpeter kit. This kit was designed not only for static but also for RC. The static version has some extra details and modifications, reminds me the, T-34 from WSN, a brand with which Trumpeter sold the T-34 RC. The philosophy of the T-72 is the same, I still believe that the T-34 gearbox with its motors, would fit in the hull. Perfectly.  

By Mario Covalski

Building and improving the Italeri / Protar Alfa Romeo 179 1980 1/12 scale In May 2001 I wrote a brief preview on the Protar's 1/12 Alfa Romeo 179. This wonderful Formula One was one of the few cars in modern F1 history which chassis and engine were the same brand. Is this model really difficult? This is the key question for this model, and the answer is NO. If it were a Tamiya model, that is to say the same matrix but injected with Tamiya plastic and having the quality control of this huge Japanese company, I would say that this is one of the most delicious models I have ever built. Unfortunately, it has some flaws, mainly due to its poor quality than to the work of the Protar craftsmen.

By Mario Covalski

Tamiya Caterhams, a step by step guide for novices 1/12 scale The first Catherham from Tamiya coming to my hands at the end of 1994, was the “Cycle Fender Special” (10202), since the “Super Seven BDR was out of stock, and it was impossible for me to get it from the stores I used to buy kits. From that moment on, my affair with which, I think is the best scale car kit ever produced, began. And here my comment: probably, you have seen better detailed kits, or even superb models limited editions.

By Rick & Jannine Bennett

Learning to paint figures step by step

By Mario Covalski

Building 1/12 F1 resin model kits: A step by step guide for novices This article aims at offering an illustrated guide, with pictures, explaining step by step the tasks that should be done, how to and the reasons, it’s basically a visual guide, based on the construction of two MG models: the 2002 Ferrari and the 2003- GA.

By Jose Antonio Solbes

How to paint with lacquers

By Mario Covalski

Building the IDF M50 radio controled Sherman 1/16 scale Building the M50 in 1/16 scale is a project I have had in mind for many years, and after the M51s (from the article published in May 2012) I felt the need to continue with this one. In this article, I’ll share with the reader my experience in building the M50 RC 1/16 from a Tamiya M4 -105mm with HVSS suspension.

By Mario Covalski

Building the Pocher Lamborghini Huracan, step by step, painting guide and tips. 1/8 scale These are the new times of Pocher, hand in hand with Hornby, the brand that offer models which represent high technology subjects as Lamborghini cars and Ducati motorcycles. Manufactured by Ixo, the Chinese company, they are the fashion of the time, huge 1/8 scale cars with metal body and chassis, already painted (luckily!). They compete with Amalgam and other brands with less expectations but to fit any budget and if you have some experience as model builder, the result will be acceptable and even excellent. The aim of this tutorial is to share the step by step in the Lamborghini Huracán construction, the last Pocher issue explaining the work achieved so that it may be useful for less experienced modelers and collectors.

By Claudio Kalicinski

Scratchbuilding the Nieuport 6H, 1/48 scale I decided to scratchbuild this plane after seeing the scale drawings by Mike Fletcher in his web site: The Nieuport Pages. I sent an E-mail to him and he kindly sent me pictures and larger resolution scale drawings. Once I enlarged the plans to 1/48, I noticed how big the plane was....

By Ricardo Gonzalez

Building and customizing the Tamiya Ducati Panigale S 1/12 scale The Ducatti Panigale is to my liking one of the most spectacular motorcycles of the past decade. Thanks to Tamiya we can have a model of it, both were the reasons why I decided to build it trying to get the most detailed model I could , taking advantage of the fact that as it was a mass production model, it would be possible for me to get a lot of references. Not only I built and superdetailed the model, but also made a slightly and own customized version, a real Panigale, as I would like to have. The aim of this article, is to show with pictures and their comments the work accomplished as a guide and to give ideas of the details that can be added or showing in some cases how to do the different tasks.

By Mario Covalski

Improving the Dragon Kubelwagen 1/6 scale # 75003 Action figure collecting is one of the most popular hobbies in the world. Figures made out of different plastic materials based on TV sci-fi series, sci-fi movies (for instance GI Joe action figures) and facts from real life such as the representation of different war scenarios. Soldier figures are commonly made in 1/6 scale, they’re represented with military uniforms made from genuine fabric and the weapons that real soldiers use to have, vehicles included.

By Gary Wickham

Advanced techniques: Building the P-51D Mustang "Lt Col John Myers" Petie 3rd Dragon 1/32 scale The infamous Dragon P-51D in 1/32. This model was started before Tamiya announced their kit, and I have to admit that during this build I did consider scrapping it more than once. In the end, I am very glad I did not. Despite the challenges and limitations of this kit, I am very happy (and proud) of the end result.

By Mario Covalski

Realistic wire wheels for 1/12 scale motorcycles One of the biggest challenges for a modeler who builds motorcycles in 1/12 scale, is to modify a wire wheel and make it look realistic; specially without having to buy an aftermarket kit. Anyway, there are no kits for this kind of modification (except for one of the Acu-stion for the Tamiya XV1600 kit), so it's not possible to get one. So any modeler attempting to do this task must rely in his/her ability in order, to get a good result.

By Denis R.S.Bomfim

Building rusted cars - VW 1966 - 1/24 scale It all started with a joke, I built a rusted Mustang GT 350 to make a gift to a friend who only builds Mustangs. It was at a modelers meeting when he received a homage and the joke consisted of letting him know the arduous remodeling and restoration work he would have with this rusted Mustang. I took advantage of my work and presented it in a contest that took place in Campinas city. Finally, the model was “best of the show” and they called me mad for giving a winning model. My answer was.... I will have to make another rusted model for me.

By Mario Covalski

Improving the Dragon Schwimmwagen - 1/6 scale #75013 Being a car fan, everything that has wheels attracts my attention, nevertheless, the Kubelwagen’s amphibious sibling, went unnoticed by me for quite a long time. After building the 1/6 Dragon Kubel, I was pretty excited with the Schwimmwagen, and the quality of the kit and improvements Dragon introduced a couple of years after the Kubel release, really surprised me. This article aims at offering my view about this kit construction, adding some improvements I considered necessary so as to make a worthy scale model.